Block Diagram | Evaluation Board | Download | Buy MMlpc213x

Features

LPC213x microcontroller

• 32-bit ARM7TDMI core
• From 32 to 512kB in system programmable flash memory
• From 8 to 32kB RAM memory
• In-System/In-Application Programming (ISP/IAP) via on-chip boot-loader software
• 2 timers with input capture, output compare and PWM functions 
• 2 UART interfaces
• 2  I2C interfaces
• SPI interface
• One (LPC2131/32) or two (LPC2134/36/38) 8 channel 10-bit A/D converters
• Single 10-bit D/A converter
• Up to 47 5 V tolerant general purpose I/O pins
• Vectored interrupt controller with configurable priorities and vector addresses
• Power saving modes
• RTC clock
• Single power supply 3.3V (internal 1.8V regulator)
• JTAG interface

MMlpc213x minimodule

• Complete, ready to use microprocessor system
• Fast ARM microcontroller LPC213x with up to 60 MIPS throughput
• Serial DataFlash memory 32Mb (4MB)  
• Reset circuit
• Built-in 12MHz crystal resonator
• Built-in 32.768kHz crystal resonator for RTC
• Possibility to mount backup battery for RTC
• Built-in 3.3V 400mA regulator
• Module supply voltage: 3.3V or 3.8 - 16V
• 2 x 26 terminals with 0.1" (2.54mm) pitch fitting every prototype board
• Small dimensions:36mm x 36mm (1400x1400mils)
• Available evaluation board and sample applications

Block diagram

A block diagram of MMstr71xf minimodule is shown on the image below:

All signals of the module are led to two 26-pin terminals with 0.1'' (2.54mm) pitch, which simplifies designing of base boards and allows use of module with prototype boards.

Evaluation Board

In order to facilitate the design of equipment using the minimodule, an evaluation board has been developed (EVBlpc213x). It includes the following elements:

Socket for the MMlpc213x module
Connector with all terminals of the MMlpc213x module
Connectors of all peripherals accessible on board
+5V power supply
włącznik zasilania
Power switch
Two RS232 ports with LED diodes
1-Wire connecor
JTAG connector for in system programming and debugging
connector for 2x16 LCD display
8 LED diodes
4 push-buttons
2 potentiometers
Buzzer
Prototype design area

Download

MMlpc213x

MMlpc213x Schematics MMlpc213x User Manual

rev. 1.0   [90 kB] (1 page, 06/05) rev. 0.8   [1 MB]  ( pages, 06/05)

LPC213x

Philips Site  LPC213x Datasheet  LPC213x User Manual   The Insider's Guide To The Philips ARM7-Based Microcontrollers

[200kB]   (41 pages, 04/05) [1.5MB]   (264 pages, 11/04)

DataFlash

AT45DB321C Datasheet  Using Atmel's DataFlash

[250 kB]  (40 pages, 06/05) [190 kB]  (30 pages, 11/02)

Demonstration software

The module and evaluation board are delivered with exemplary software, written in C language with use of Rowley CrossWorks environment. Exemplary software includes:

• LED: simple program showing light effect on the led diodes.
• USART: demonstrates configuring and writing to a UART
• LCD: shows text on LCD with use of 4-bit mode
• 1-WIRE: program reads temperature from DS18B20 1-wire thermometer and displays it on the lcd.
• DATAFLASH: use of SPI bus and AT45DB321C DataFlash memory
•  Software 

Minimodule is sold with CD-ROM, which contains documentations and software.

Note: Net prices